Using a 2nd IMU

From STorM32-BGC Wiki V1
Revision as of 18:57, 8 January 2015 by OlliW (talk | contribs)
Jump to navigation Jump to search

The STorM32 controller allows the use of a 2nd IMU, in addition to the camera IMU installed on the camera platform, for superior performance. It's usage and advantages are described here.

Installation Options

The basic "rule" for installation is simple:

The second IMU must be mounted on the "gimbal support" above the yaw motor so it is not moved by any of the motors. 

It must not be mounted on one of the gimbal axes or the camera platform.

So you can either mount the controller mainboard on the gimbal support using the onboard IMU as 2nd IMU, or put the mainboard somewhere else (on the yaw axis for example) and mount an external IMU module above the yaw motor. These two options are shown as option (1) and (2) in the diagram below.

The external IMU module has to be connected to the I2C#2 connector on the bottom side of the STorM32 board. Doing so automatically selects the external IMU module as 2nd IMU. If no IMU module is connected to I2C#2, the onboard IMU is selected. So you don't have to change anything in the GUI, the external IMU is used automatically when connected.

Comment: The onboard mpu6050 IMU is connected to the I2C#2 connector internally and is set to a non default i2c adress. If you connect an external IMU to the I2C#2 connector it hence can be recognised by its default i2c adress.

Comment: The configuration (3) in the diagram is NOT supported by the STorM32 firmware, as by principle it provides only very limited benefits.

Storm32-wiki-2nd-imu-configurations-01.jpg

IMU Orientation

For a correct function it is extremly important to set the IMU orientation correctly, i.e., to choose the parameter field Imu2 Orientaion in the [Gimbal Configuration] tab.

This is most conveniently achieved by using the [Configure Gimbal Tool]. Alternatively, it may be set manualy following the recipe described in Manually Setting the IMU Orientation.

Calibration

As with the camera IMU, also the 2nd IMU, be it the onboard IMU or an external IMU module, needs to be calibrated for optional performance.

However, fortunately, for the 2nd IMU it's not critical to get the most accurate calibration, and a good 1-point calibration should be enough for most situations. Exceptions are then motors with high motor pole counts, larger than 14, are used.

The calibration of the 2nd IMU works similar to the camera IMU, one only has to select the 2nd IMU in the respctive fields.

IMU Configuration

The 2nd IMU support is activated via the parameter Imu2 Configuration found in the [Setup] tab. To activate the 2nd IMU, set it to

  • "gimbal support": activate 2nd IMU above the yaw motor
  • "gimbal support xy": activate 2nd IMU ybove the yaw motor rotated by 45°.

Benefits of a 2nd IMU

Nowadays any advanced brushless gimbal controller provides 2nd IMU support, but there are marked differences in how and to what extend the 2nd IMU is used. The STorM32 controller is - to the best of the knowledge of the firmware author - unique in that it provides (i) a stable operation with the 2nd IMU above the yaw motor and (ii) a distortion rejection for the yaw axis also in the pan/follow mode. Usually these features would require the installation of a poti or angle encoder on yaw.

The benefits provided by the STorm§2 controller are

  • significantly improved accuracy, i.e., the position of the camera is held constant with a much smaller error bandwidth much higher degree
  • drastically larger range of operation, essentially any pitch and yaw angle is possible (for a more detailed discussion of the possibilities and limitations see here)
  • stable operation of teh 2nd IMU above the yaw axis without dterioration over time due to gyro drift
  • always keeps or returns to the correct yaw orientation, also when in pan/follow mode

These features were demonstrated for an early test version of the firmware (the features became better since then) in this video: