Where to get NT Modules: Difference between revisions

From STorM32-BGC Wiki V1
Jump to navigation Jump to search
No edit summary
No edit summary
 
(9 intermediate revisions by the same user not shown)
Line 1: Line 1:
Pre-assembled ready-to-use NT modules are currently - unfortunately - not available commercially.  
Pre-assembled, ready-to-use NT modules are currently not available commercially. However, the CC3D Atom can easily be used as a NT Imu module, and may be the best choice currently, if DIY is not an option.


However, the CC3D Atom can easily be used as a NT Imu module. The GLB mini CC3D atom provides the most compact solution but is more currently probably the best option, or when shipping time matters the BG CC3D atom (see post #2 for links).
== CC3D Atom ==


The [https://www.openpilot.org/openpilot-atom/ Open Pilot CC3D Atom] can be used as NT imu module, when flashed with the respective NT firmware. With the pin headers stripped off, it is also relatively small.


[B]CC3D atom NT imu modules:[/B]
The Mini CC3D is even smaller, without the need of hardware modifications. Unfortunately it can be first-time flashed only via SWD, and a ST-Link programmer is additionally needed for converting it into a NT module.


the [URL="https://wiki.openpilot.org/display/WIKI/CopterControl+-+CC3D+-+Atom+Hardware+Setup"]Open Pilot CC3D Atom[/URL] can be used as NT imu module, when flashed with the respective NT firmware
Both boards are available cheaply from various Asian sources, and of course also at somewhat higher prices in many "regular" shops.
when stripped off the pin headers it is smaller than the above "big" v1.0 NT imu modules, this is not necessary for the "mini CC3D atom"
it is available cheaply from various Asian sources, and of course at somewhat higher prices in many "regular" shops, and can come in various different hardware flavors
some links
- [url]http://www.banggood.com/OpenPilot-CC3D-Atom-Mini-CC3D-FPV-Flight-Controller-CC3D-EVO-p-970762.html[/url] (ships straight from EU or USA warehouses!)
- [url]http://www.goodluckbuy.com/openpilot-mini-cc3d-atom-nano-cc3d-side-pin-flight-controller-for-fpv-qav-250-400-quadcopter-.html[/url]
- [url]http://www.aliexpress.com/wholesale?catId=0&initiative_id=SB_20150822235223&isPremium=y&SearchText=openpilot+cc3d+atom[/url]
- [url]http://www.goodluckbuy.com/mini-cc3d-32-bit-openpilot-open-source-flight-controller-processor-with-case.html[/url]
- [url]http://www.banggood.com/Openpilot-MINI-CC3D-NANO-Atom-Flight-Controller-for-QAV250-Multicopter-250-Frame-Kit-p-992324.html[/url]


the "mini CC3D atom" is currently probably the best and easiest and cheapest solution to get a NT imu module
Some links:
* [http://www.banggood.com/OpenPilot-CC3D-Atom-Mini-CC3D-FPV-Flight-Controller-CC3D-EVO-p-970762.html CC3D Atom @ banggood]
* [http://www.goodluckbuy.com/openpilot-mini-cc3d-atom-nano-cc3d-side-pin-flight-controller-for-fpv-qav-250-400-quadcopter-.html CC3D Atom @ goodluckbuy]
* [http://www.aliexpress.com/wholesale?catId=0&initiative_id=SB_20150822235223&isPremium=y&SearchText=openpilot+cc3d+atom CC3D Atom @ aliexpress]
* [http://www.goodluckbuy.com/mini-cc3d-32-bit-openpilot-open-source-flight-controller-processor-with-case.html Mini CC3D @ goodluckbuy]
* [http://www.banggood.com/Openpilot-MINI-CC3D-NANO-Atom-Flight-Controller-for-QAV250-Multicopter-250-Frame-Kit-p-992324.html Mini CC3D @ banggood]


== Cables and Connectors ==


[B]Sources for cables:[/B]
Unfortunately I don't know about a cheap and readily available source of suitable pre-configured cables with plugs. The 1 mm JST has however become kind of a standard in the RC world, and used for e.g. flight controllers, gimbal controllers, etc., which gives options.
 
Unfortunately I don't know about a good, i.e reasonably priced and readily available, source of suitable pre-configured cables with plugs. The 1mm JST has however become kind of a standard and is used by many electronics, such as flight controllers, AM gimbal controllers, etc., which gives options.  
Some options:
Some options I know a about are:
* ReadyToFlyQuads/witespy: [http://www.readytoflyquads.com/cables]. Explore the shop carefully and study the various options for configuration which are offered, with the right clicks it actually has some good deals.
* ReadyToFlyQuads/witespy: [url]http://www.readytoflyquads.com/cables[/url]
* Viacopter: [https://www.viacopter.eu/multirotor-shop/accessories/connectors-and-wires]
explore the shop carefully and study the various options for configuration which are offered, with the right clicks it offers actually some good deals
* Goodluckbuy: [http://www.goodluckbuy.com/bgc-2-0-brushless-gimbal-driver-sensor-connection-cable-for-gimbal-controller.html]. The silicon wires are not as flexible as for other imu module wires, but in lack of better options OK. Quite expensive.
* Viacopter: [url]https://www.viacopter.eu/multirotor-shop/accessories/connectors-and-wires[/url]
* Flyduino: [http://flyduino.net/Brushless-Gimbal-Kamerastabilisierung]
* Goodluckbuy: [url]http://www.goodluckbuy.com/bgc-2-0-brushless-gimbal-driver-sensor-connection-cable-for-gimbal-controller.html[/url]  
The silicon wires are not as flexible as for other imu module wires, but in lack of better options OK. Quite expensive.
* Flyduino: [url]http://flyduino.net/Brushless-Gimbal-Kamerastabilisierung[/url]

Latest revision as of 22:12, 26 November 2015

Pre-assembled, ready-to-use NT modules are currently not available commercially. However, the CC3D Atom can easily be used as a NT Imu module, and may be the best choice currently, if DIY is not an option.

CC3D Atom

The Open Pilot CC3D Atom can be used as NT imu module, when flashed with the respective NT firmware. With the pin headers stripped off, it is also relatively small.

The Mini CC3D is even smaller, without the need of hardware modifications. Unfortunately it can be first-time flashed only via SWD, and a ST-Link programmer is additionally needed for converting it into a NT module.

Both boards are available cheaply from various Asian sources, and of course also at somewhat higher prices in many "regular" shops.

Some links:

Cables and Connectors

Unfortunately I don't know about a cheap and readily available source of suitable pre-configured cables with plugs. The 1 mm JST has however become kind of a standard in the RC world, and used for e.g. flight controllers, gimbal controllers, etc., which gives options.

Some options:

  • ReadyToFlyQuads/witespy: [1]. Explore the shop carefully and study the various options for configuration which are offered, with the right clicks it actually has some good deals.
  • Viacopter: [2]
  • Goodluckbuy: [3]. The silicon wires are not as flexible as for other imu module wires, but in lack of better options OK. Quite expensive.
  • Flyduino: [4]
Retrieved from "http:///storm32bgc-v1-wiki/index.php?title=Where_to_get_NT_Modules&oldid=2989"