Flashing OlliW's NT Modules: Difference between revisions
No edit summary |
|||
| Line 7: | Line 7: | ||
'''1.''' You will need a standard USB-TTL adapter (see [[STorM32_FAQ#Which USB-TTL adapter should I use.3F|FAQ: Which USB-TTL adapter should I use?]]). Ensure that it is working (drivers installed, etc.). | '''1.''' You will need a standard USB-TTL adapter (see [[STorM32_FAQ#Which USB-TTL adapter should I use.3F|FAQ: Which USB-TTL adapter should I use?]]). Ensure that it is working (drivers installed, etc.). | ||
'''2.''' Connect the | '''2.''' Connect the USB-TTL adapter to the NT bus pins on the NT bus connector. Do not yet power the NT module. | ||
'''3.''' Find the BOOT0 solder jumper and close it. | '''3.''' Find the BOOT0 solder jumper on the NT module and close it. | ||
:[[File:Storm32-nt-firmware-first-time-flashing-01.jpg|640px]] | :[[File:Storm32-nt-firmware-first-time-flashing-01.jpg|640px]] | ||
'''4.''' Now power up the NT module, e.g. by connecting the NT bus connector's VCC pin to the 3.3 V or 5 V pin (either is fine) on the USB-TTL adapter. | '''4.''' Now power up the NT module, e.g., by connecting the NT bus connector's VCC pin to the 3.3 V or 5 V pin (either is fine) on the USB-TTL adapter. | ||
'''5.''' | '''5.''' In the STorM32 GUI go to the {{GUI|Flash Firmware}} tab and choose your settings. | ||
:[[File:Storm32-nt-firmware-first-time-flashing-gui-screen-02.jpg|640px]] | :[[File:Storm32-nt-firmware-first-time-flashing-gui-screen-02.jpg|640px]] | ||
'''6.''' Select the | '''6.''' Select the correct NT module and the desired firmware version in the respective combo boxes {{GUIFIELD|Board}} and {{GUIFIELD|Firmware Version}}. | ||
'''7.''' Open the BOOT0 solder jumper again. The NT module is now ready for usage. | '''7'''. Select {{GUIPARAM|System Bootloader @ UART1}} in the {{GUIFIELD|STM32 Programmer}} field. | ||
'''8'''. In the {{GUIFIELD|Com Port}} field select the COM port which your USB-TTL adapter is connected to. | |||
'''9'''. Finally, hit the {{GUIFIELD|Flash Firmware}} button. | |||
'''10'''. Now a black window (DOS console) should open and run the flash loader program. Wait until it is finished (takes some seconds). | |||
'''11'''. Open the BOOT0 solder jumper again. The NT module is now ready for usage. | |||
== First-Time Flashing Using SWD == | == First-Time Flashing Using SWD == | ||
Revision as of 09:09, 26 May 2018
On all "OlliW" NT modules the BOOT0 pin is exposed as a solder jumper, and each module can thus be first-time flashed using a standard USB-TTL adapter. Most modules also have the SWD pins exposed, which allows a first-time flashing via a ST-Link adapter. Both flashing methods are fully supported by the GUI. Any subsequent flashing (updating) can be performed using the simpler procedures described in Updating the Firmware of NT Modules.
First-Time Flashing Using a USB-TTL Adapter
1. You will need a standard USB-TTL adapter (see FAQ: Which USB-TTL adapter should I use?). Ensure that it is working (drivers installed, etc.).
2. Connect the USB-TTL adapter to the NT bus pins on the NT bus connector. Do not yet power the NT module.
3. Find the BOOT0 solder jumper on the NT module and close it.
4. Now power up the NT module, e.g., by connecting the NT bus connector's VCC pin to the 3.3 V or 5 V pin (either is fine) on the USB-TTL adapter.
5. In the STorM32 GUI go to the [GUI:Flash Firmware] tab and choose your settings.
6. Select the correct NT module and the desired firmware version in the respective combo boxes [Board] and [Firmware Version].
7. Select "System Bootloader @ UART1" in the [STM32 Programmer] field.
8. In the [Com Port] field select the COM port which your USB-TTL adapter is connected to.
9. Finally, hit the [Flash Firmware] button.
10. Now a black window (DOS console) should open and run the flash loader program. Wait until it is finished (takes some seconds).
11. Open the BOOT0 solder jumper again. The NT module is now ready for usage.
First-Time Flashing Using SWD
1. You will need a ST-Link V2 Programmer or similar. Ensure that it is working (drivers installed, etc.).
2. Connect the programmer to the SWD pins on the NT module.
3. From the STorM32 GUI select the Flash Firmware Tab and set the fields as seen below. The [Board] field should be set to the NT module type you want to flash, and the [Firmware Version] selected as desired.
4. Select the Flash Firmware button and a DOS window opens similar to below:
Updating Firmware
For updating the NT firmware you may again use the methods described before, but preferably the "canonical" procedure described in Updating the Firmware of NT Modules.