Using STorM32 with ArduPilot: Difference between revisions

From STorM32-BGC Wiki
Jump to navigation Jump to search
Tag: Manual revert
 
(299 intermediate revisions by the same user not shown)
Line 1: Line 1:
''The information on this page refers to firmware v2.40 and BetaCopter v010, and higher.''
''The information on this page refers to firmware v2.64e, and higher.''


The STorM32 gimbal controller can communicate with an [http://ardupilot.org/ardupilot/index.html ArduPilot] flight controller via (i) a serial UART data line or (ii) the CAN bus using the UAVCAN protocol. The serial/UAVCAN communication allows for a much richer data transmission and accordingly richer set of features than possible with the traditional PWM connections. Examples are advanced control functions or the [[STorM32-Link]]. It also leads to a clean wiring.
The STorM32 gimbal controller can communicate with an [http://ardupilot.org/ardupilot/index.html ArduPilot] flight controller via a serial UART data link. The serial communication allows for a much richer data transmission and accordingly richer set of features than possible with the traditional connections such as PWM, PPM, SBUS, CRSF, and alike.


If you just need the range of functionality possible with the standard tilt & pan control, then you don't need anything of the following, and you may stop reading here. Also, some of the features discussed below can be accomplished by workarounds. Decide yourself which approach fits your needs best. :)
If you only need the range of functionality possible with the conventional tilt & pan control, then you may not need anything of the following. Some of the basic features can also be accomplished in traditional ways. Decide yourself which approach fits your needs best. :)
 
If you want to make best use of your STorM32 gimbal and want 2020-ish capabilities, then you may want to chose [https://github.com/olliw42/BetaPilot BetaPilot] (BetaCopter/BetaPlane). This fork of ArduPilot is specifically designed for the STorM32 gimbal controller, and provides the best range of functions. For details see [[Using STorM32 with BetaPilot]].
 
<div class="toclimit-3">__TOC__</div>


== STorM32 - ArduPilot Support ==
== STorM32 - ArduPilot Support ==


ArduPilot offers two mounts, which can be used with the STorM32 controller, the '''''STorM32 Mavlink''''' (MNT_TYPE = 4) and '''''STorM32 Serial''''' (MNT_TYPE = 5) mount types. For further details please visit [http://ardupilot.org/copter/docs/common-storm32-gimbal.html#common-storm32-gimbal| ArduPilot Docs > Copter > Optional Hardware > Camera&Gimbals > SToRM32 Gimbal Controller]. A good sum-up by lvale for the STorM32 Mavlink Mount is found here [http://www.rcgroups.com/forums/showpost.php?p=35263645&postcount=154], and a workaround to access further STorM32 functions here [http://www.rcgroups.com/forums/showpost.php?p=34415407&postcount=115].
'''''ArduPilot''''' offers three mount types, which can in principle be used with the STorM32 controller:
 
* '''''SToRM32 MAVLink''''': MNTx_TYPE = 4
* '''''SToRM32 Serial''''': MNTx_TYPE = 5
* '''''Greemsy''''': MNTx_TYPE = 6
 
For further details on the first two mounts, and instructions on how to use them, please visit [http://ardupilot.org/copter/docs/common-storm32-gimbal.html#common-storm32-gimbal| ArduPilot Docs > Copter > Optional Hardware > Camera&Gimbals > SToRM32 Gimbal Controller].
 
The ''SToRM32 Serial'' mount (MNTx_TYPE = 5) does not work with v2.xx firmwares, and should not be considered except for legacy I2C setups running v0.9x firmware.
 
The ''Greemsy'' mount (MNTx_TYPE = 6) is MAVLink based, and thus can in principle be used with STorM32. This mount in fact exploits the 'new' gimbal messages of the [https://mavlink.io/en/services/gimbal_v2.html gimbal protocol v2], and would offer some real benefits. However, it unfortuntaley violates and breaks the MAVLink standard in various respects, and interoperability with STorM32 is thus mixed.
 
The ''SToRM32 MAVLink'' mount (MNTx_TYPE = 4) currently appears to work best with STorM32 in the sense that it produces the least issues, but it is quite limited in its functionality.
 
For both the ''SToRM32 MAVLink'' (MNTx_TYPE = 4) and ''Greemsy'' (MNTx_TYPE = 6) mounts, it is not fully clear what works and what does not work at the time of writing, but the ''SToRM32 MAVLink'' mount (MNTx_TYPE = 4) should work fine with respect to controlling a STorM32 gimbal.
 
'''''Disclaimer''': ArduPilot's gimbal support is a constant source of issues, in terms of incompatibilities with the official MAVLink standard and/or flaws, and the details can quite vary with the ArduPilot firmware version. Also the ArduPilot documentation can be out-of-date. Please note that STorM32 can't do anything about this, it's ArduPilot, and please also note that the STorM32 firmware author is neither responsible for the implementation of ArduPilot's mount types nor for ArduPilot's documentation.''


{{COMMENT|Unfortunately, ArduPilot's gimbal support is partially flawed, which is true especially for its MAVLink mount. That is, some features you will find to work nicely, some others you will find to not work. There is nothing the STorM32 or any gimbal controller can do about it; it's ArduPilot. Please note that the STorM32 firmware author is not responsible for the implementation of these two mounts; again, it's ArduPilot.}}
== Virtual Channel Configuration ==


The '''''BetaCopter''''' fork of ArduPilot additionally offers the '''''STorM32 Native''''' (MNT_TYPE = 83) mount type, and '''''Serial UAVCAN Tunnel''''' ports for communicating via the CAN bus instead of a serial bus. These additions were created and are maintained by the STorM32 firmware developer and provide the best range of functions.
ArduPilot does not emit the RC_CHANNELS MAVLink message by default, which could be desired for taking advantage of the STorM32's virtual channel feature.


A comparison of the different techniques to connect the STorM32 controller with the flight controller is given in the following feature matrix.
It can be activated in the flight controller by setting the SRx_RC_CHAN parameter to a non-zero value, where 'x' refers to the stream associated to the serial port which is used for the MAVLink communication with the STorM32 controller.


=== Feature Matrix ===
For more details on the feature see [[Using_STorM32_with_BetaPilot#Virtual_Channel_Configuration|Virtual Channel Configuration]].
(to the best of the authors knowledge)
<!--
== Feature Matrix ==
(for ArduPilot 4.2)(the status for ArduPilot 4.3 is presently unclear)(all to the best of the authors knowledge)
{| class="wikitable" style="text-align: center;"
{| class="wikitable" style="text-align: center;"
!Feature
!Feature
!PWM
!Traditional<br>PWM, PPM, SBUS, ...
!STorM32 Mavlink
!SToRM32 MAVLink<br>(MNT_TYPE = 4)
!STorM32 Serial
!SToRM32 Serial<br>(MNT_TYPE = 5)
!STorM32 Native
!BetaPilot<br> STorM32 MAVLink2<br>(MNT_TYPE = 83)
|-
| style="text-align:left;" | Gimbal Angle Control || style="background-color: lightgreen;"| x || style="background-color: #d2f8d2;"| x <sup>(?)</sup> || style="background-color: lightgreen;"| x || style="background-color: lightgreen;"| x
|-
|-
| style="text-align:left;" | Gimbal Angle Control || style="background-color: lightgreen;"| x || style="background-color: lightgreen;"| x <sup>(?)</sup> || style="background-color: lightgreen;"| x || style="background-color: lightgreen;"| x
| style="text-align:left;" | MOUNT_STATUS message || - || style="background-color: #d2f8d2;"| x <sup>(1)</sup> || style="background-color: #d2f8d2;"| x <sup>(2)</sup> || style="background-color: lightgreen;"| x
|-
|-
| style="text-align:left;" | Solo Smart Shots || style="background-color: lightgreen;"| x || - || - || style="background-color: lightgreen;"| x
| style="text-align:left;" | ATTITUDE message || - || - || - || style="background-color: lightgreen;"| x
|-
|-
| style="text-align:left;" | MAV_MOUNT_STATUS message || - || style="background-color: lightgreen;"| x <sup>(1)</sup> || style="background-color: lightgreen;"| x <sup>(2)</sup> || style="background-color: lightgreen;"| x
| style="text-align:left;" | Camera Trigger || style="background-color: lightgreen;"| x || style="background-color: lightgreen;"| x || - || style="background-color: lightgreen;"| x
|-
|-
| style="text-align:left;" | Camera Trigger || style="background-color: lightgreen;"| x || style="background-color: lightgreen;"| x <sup>(?)</sup> || - || style="background-color: lightgreen;"| x
| style="text-align:left;" | Gimbal Point in MP || - || style="background-color: lightgreen;"| x || style="background-color: #d2f8d2;"| x <sup>(2)</sup> || style="background-color: lightgreen;"| x
|-
|-
| style="text-align:left;" | Gimbal Point in MP || - || style="background-color: lightgreen;"| x <sup>(?)</sup> || style="background-color: lightgreen;"| x || style="background-color: lightgreen;"| x
| style="text-align:left;" | Solo Smart Shots || style="background-color: #d2f8d2;"| x <sup>(3)|| - || - || style="background-color: #d2f8d2;"| x <sup>(3)</sup>
|-
|-
| style="text-align:left;" | Video on/off || - || - || - || style="background-color: lightgreen;"| x
| style="text-align:left;" | Camera Manager in QGC || - || style="background-color: lightgreen;"| x || - || style="background-color: lightgreen;"| x
|-
|-
| style="text-align:left;" | RC Targeting relative/absolute || - || - || - || style="background-color: lightgreen;"| x
| style="text-align:left;" | MAVLink Parameters || - || style="background-color: lightgreen;"| x || - || style="background-color: lightgreen;"| x
|-
|-
| style="text-align:left;" | 360° Gimbal with Free Look || - || - || - || style="background-color: lightgreen;"| x
| style="text-align:left;" | Video Control in Missions || - || style="background-color: lightgreen;"| x || - || style="background-color: lightgreen;"| x
|-
|-
| style="text-align:left;" | STorM32 Functions || - || - || - || style="background-color: lightgreen;"| x
| style="text-align:left;" | 360° Gimbal with Free Look || style="background-color: lightgreen;"| x || - || - || style="background-color: lightgreen;"| x
|-
|-
| style="text-align:left;" | STorM32 Scripts || - || - || - || style="background-color: lightgreen;"| x
| style="text-align:left;" | STorM32 Functions || style="background-color: lightgreen;"| x || - || - || style="background-color: lightgreen;"| x
|-
|-
| style="text-align:left;" | STorM32-Link: Horizon Drift Comp. || - || - || - || style="background-color: lightgreen;"| x <sup>(3)</sup>
| style="text-align:left;" | STorM32 Scripts || style="background-color: lightgreen;"| x || - || - || style="background-color: lightgreen;"| x
|-
|-
| style="text-align:left;" | STorM32-Link: Yaw Drift Comp. || - || - || - || style="background-color: lightgreen;"| x <sup>(3)</sup>
| style="text-align:left;" | STorM32-Link: Horizon Drift Comp. || - || - || - || style="background-color: lightgreen;"| x <sup></sup>
|-
|-
| style="text-align:left;" | Passthrough Configuration || - || - || - || style="background-color: lightgreen;"| x
| style="text-align:left;" | STorM32-Link: Yaw Drift Comp. || - || - || - || style="background-color: lightgreen;"| x <sup></sup>
|-
|-
| style="text-align:left;" | Solo Gimbal Mimicry || - || - || - || style="background-color: lightgreen;"| x
| style="text-align:left;" | MAVLink Passthrough Configuration || - || style="background-color: lightgreen;"| x || - || style="background-color: lightgreen;"| x
|-
| style="text-align:left;" | MAVLink Camera Microservice || - || style="background-color: lightgreen;"| x || - || style="background-color: lightgreen;"| x
|-
| style="text-align:left;" | MAVLink Advanced Features || - || - || - || style="background-color: lightgreen;"| x
|-
| style="text-align:left;" | MAVLink Statustext messages || - || - || - || style="background-color: lightgreen;"| x
|-
| style="text-align:left;" | STorM32 Gimbal Protocol || - || - || - || style="background-color: lightgreen;"| x
|-
| style="text-align:left;" | Prearm Checks || - || - || - || style="background-color: lightgreen;"| x
|}
|}


(?) May or may not work properly in the latest ArduPilot releases, see the comment in the introduction. Please check with the ArduPilot community.
(?) Many but not all features work in the latest ArduPilot releases. Please check with the ArduPilot community.


(1) The message reports the last set point, not the actual gimbal/camera orientation.
(1) The message reports the last set point, not the actual gimbal/camera orientation.


(2) Works only for deprecated v0.xx firmwares.
(2) Works only for deprecated v0.9x firmwares.
 
(3) Works only for T-STorM32 gimbals.
 
== BetaCopter ==
 
Some modifications to the ArduCopter firmware were made and the result called BetaCopter, which provides simply the best support of STorM32 gimbals.
 
'''''Comments:'''''
* ''If you are satisfied with ArduPilot's gimbal support then there is really no need to use BetaCopter. However, if you want to make best use of the STorM32's features and capabilities then you want to chose BetaCopter.''
* ''Before using BetaCopter it is '''strongly''' recommended to first install the original ArduCopter firmware and get the copter flying flawlessly with it, and only then to install BetaCopter.''
 
BetaCopter comes in two variants:
* The ''''''full' version''''' is derived from ArduPilot master, and includes the full set of additions, including all UAVCAN and UC4H additions.
* The ''''''s' version''''' ('s' for serial) in contrast is derived from Copter 3.6. It includes all STorM32 additions, but not any UAVCAN or UC4H addition. It is a straight forward, minimal intrusive extension of Copter-3.6.
 
The latest versions of BetaCopter and the STorM32 firmware can be downloaded from here: [[Downloads]].
 
In order to establish a working communication between the STorM32 and the flight controller, parameters on both sides, BetaCopter and STorM32, need to be adjusted, as described in the following.
 
The BetaCopter fork implements the STorM32 Native mount type, which handles '''''all''''' of the following. For the BetaCopter 's' version this means, that if the STorM32 Native mount is not activated, it will behave exactly like the original Copter-3.6 firmware, with no side effects.
 
=== STorM32 Native via UART Port ===
----
 
The STorM32 board needs to be connected via one of its UART ports or the USB port to one of the UART ports on the ArduPilot flight controller, and these settings be made:
 
'''''Settings in BetaCopter:'''''
* MNT_TYPE = 83
* SERIALx_PROTOCOL = 83
* SERIALx_BAUD = 115
 
'''''Settings in STorM32:'''''
* {{PARAMNAME|Mavlink Configuration}} = {{PARAMVALUE|no heartbeat}}
 
With the mount activated, you should notice:
 
* All ArduCopter mount features such as gimbal control, POI, follow me, smart shots, and so on, are working.
* All ArduCopter camera features are working. That is, whenever a certain path of actions (Mavlink, receiver, mission, UAVCAN, ...) lets ArduCopter want to take a picture, the STorM32 controller will know and activate its camera functions.
* In the Message box of MissonPlanner "STorM32 ..." messages will appear.
* The STorM32-Link, providing horizon drift and yaw drift compensation, and additional features, is present.
 
{{COMMENT|The default baudrate of the STorM32 serial ports is 115200 bps, hence in ArduPilot SERIALx_BAUD has to be set to 115. However, other baudrates can be configured; for e.g. 230400 bps one sets the STorM32 parameter {{PARAMNAME|Uart Baudrate}} to {{PARAMVALUE|230400}} and the ArduPilot parameter SERIALx_BAUD to 230.}}
 
=== STorM32 Native via UAVCAN ===
----
 
The STorM32 can also be connected via the CAN bus to the ArduPilot flight controller. The communication is then established by using one of the serial UAVCAN tunnels (SERIALTNLx) in BetaCopter, instead of a UART (SERIALx) port. Function-wise this configuration is identical to using a serial port, except of course that the data communication is now via the CAN bus using the UAVCAN protocol. The required settings are:
 
'''''Settings in BetaCopter:'''''
* MNT_TYPE = 83
* SERIALTNLx_PROT = 83
* SERIALTNLx_CH_ID = 71
* SERIALTNLx_BAUD = 115 (is actually irrelevant in this case)
 
'''''Settings in STorM32:'''''
* {{PARAMNAME|Mavlink Configuration}} = {{PARAMVALUE|no heartbeat}}
* {{PARAMNAME|Can Configuration}} = {{PARAMVALUE|uavcan}}
* {{PARAMNAME|Uavcan Node ID}} = {{PARAMVALUE|71}}
 
The CAN bus of the flight controller must be configured in addition. This requires that additional parameters in the flight controller's CAN section must be set appropriately. Typical settings could be:
 
* CAN_D1_PROTOCOL = 1
* CAN_P1_BITRATE = 1000000
* CAN_P1_DRIVER = 1
 
Please consult the [http://ardupilot.org/ardupilot/ ArduPilot Docs] for further information.
 
{{COMMENT|The channel ID used by BetaCopter and STorM32 must be identical. The STorM32's channel ID is identical to its UAVCAN node ID, which per default is 71. Dynamic node allocation is not supported. The range of allowed IDs is restricted to 11 - 124. The STorM32 board needs to be reset for a change to become effective.}}
 
The details of the STorM32's UAVCAN support, including its configuration, are described in the article [[UAVCAN]].
 
The 'STorM32 Native via UAVCAN' option obviously requires using the 'full' version of BetaCopter, and is not available with the 's' version.
 
=== STorM32-Link ===
----
 
'''''Parameter in STorM32:'''''
* {{PARAMNAME|STorM32Link Configuration}} = {{PARAMVALUE|v1}}
 
With MNT_TYPE = 83 also the STorM32-Link is activated (for details see [[STorM32-Link]]). That is, in addition to the 'conventional' data also the data required for the functioning of the STorM32-Link are emitted by the flight controller. The parameter {{PARAMNAME|STorM32Link Configuration}} set to {{PARAMVALUE|v1}} makes the STorM32 using them. In the STorM32 GUI, specifically the {{GUI|Dashboard}} and/or the {{GUI|Data Display}}, you should note that the STorM32-Link field goes to INUSE and OK.
 
{{COMMENT|If only the 'conventional' data but not the STorM32-Link data are received by the STorM32 controller, then an ISPRESENT and/or OK will be displayed to indicate that a working link has been established between STorM32 and BetaCopter, and that the 'conventional' control functions are all working. The INUSE flag will not appear, which indicates that the STorM32-Link, i.e., the horizon and yaw drift compensation feature, is not active.}}
 
{{COMMENT|The STorM32-Link is available only for T-STorM32 gimbals, but not the conventional STorM32 NT gimbals.}}


=== STorM32: Virtual Channel Configuration ===
(3) Only up to ArduCopter 3.6. ArduCopter 4.0 has introduced two bugs which the STorM32 controller cannot work around.
----
-->
 
'''''Parameter in STorM32:'''''
* {{PARAMNAME|Virtual Channel Configuration}} = {{PARAMVALUE|serial}}
 
With this setting, all STorM32 [[Inputs and Functions|functions]] can be invoked by selecting any of the {{PARAMVALUE|Virtual-1}} - {{PARAMVALUE|Virtual-16}} input channels, exactly as one would do if the STorM32 controller would be directly connected to the receiver. This allows doing many useful things, such as activating a script or triggering video on/off from the transmitter. It however also allows doing nonsense, and it is the users responsibility to avoid that. For instance, if the ArduPilot mount is activated and is in Rc Targeting mode, and e.g. {{PARAMNAME|Rc Pitch Control}} is set to a virtual input channel, then the gimbal may move in funny ways since it may receive the transmitter stick information from both the ArduPilot mount and the receiver. In contrast, if the ArduPilot mount is in GPS or ROI Targeting mode, then one gets "free look", which is useful and quite cool actually. As said, all this is exactly as if the receiver would be directly connected to the STorM32 controller on its RC ports.
 
=== RC Targeting ===
----
 
'''''Parameter in BetaCopter:'''''
* MNT_STRM_BM
 
The BetaCopter parameter MNT_STRM_BM, which is a bit mask, allows us to enable/disable various functions. Especially the behavior of the RC Targeting mode can be modified. By setting the 1-st bit of MNT_STRM_BM, that is by adding +1 to the current value, the RC Targeting is determined now by the STorM32 parameters in the {{GUI|Rc Inputs}} tab. This especially allows us to set a relative mode.
 
=== Passthru Configuration ===
----
 
'''''Parameter in BetaCopter:'''''
* MNT_STRM_PTSER
 
This feature allows you to connect the STorM32 GUI to the USB port of an ArduPilot flight controller, or in fact to any of its serial ports, or the UAVCAN bus, and to directly communicate with the STorM32 gimbal. This is extremely convennient for configuring STorM32 gimbals when e.g. installed permanently in the flight vehicle. This also works via a wireless telemetry link, and thus opens the option of e.g. tuning the gimbal during flight, and further unheard of possibilities for controlling the gimbal during flight.
 
These two video demonstrate this feature, and also explain the setup:
 
{|
|width=370|{{#ev:youtube|lz_0BdGGuxc|360}}
|{{#ev:youtube|IF1_38fVppU|360}}
|}
 
{{COMMENT|By default the passthru communication is disabled when the flight controller is armed, and e.g. in-flight configuration would not work. This protection can be disabled by setting the 7-th bit in the MNT_STRM_BM, by adding +64 to its value.}}
 
=== Solo Gimbal Mimicry ===
----
 
'''''Parameter in BetaCopter:'''''
* MNT_STRM_BM
 
The BetaCopter parameter MNT_STRM_BM, which is a bit mask, allows us to enable/disable various functions. The Solo gimbal mimicry feature can be enabled by setting the 6-th bit of MNT_STRM_BM, that is by adding +32 to the current value. With this feature enabled, the Solo Artoo controller will believe that a Solo gimbal is installed and not display the nasty "Solo Gimbal not found" messages anymore.
 
{|
|width=370|{{#ev:youtube|jSCJNR5k6Xk|360}}
|}


== Testing the Connection ==
== Testing the Connection ==


The serial/UAVCAN connection can be tested in several ways. The following tests do not require that the copter is completely built, and do not require that the copter is armed.
The serial MAVLink connection can be tested in several ways. Suggestions can be found in [[Using_STorM32_with_BetaPilot#Testing_the_Connection | Using STorM32 with BetaPilot: Testing the Connection]]. They may not all work with native ArduPilot, but many will.
 
* '''''STorM32-Link field in the STorM32 GUI''''': The {{GUI|Dashboard}} and {{GUI|Data Display}} each have a field which is related to the STorM32-Link. They should display OK, PRESENT or a similar positive message.
 
* '''''Message box in MissonPlanner''''': In the message box several messages related to the STorM32 should appear. In particular, a message like "STorM32 v2.40 nt v1.30 F103RC" informing about the STorM32 firmware version should be visible. Also, a message "STorM32 in NORMAL mode" should occur when the gimbal has finished initialization and entered NORMAL mode.
 
* '''''Trigger Camera NOW''''': In MissionPlanner the camera can be triggered by a right-mouse-click dropdown menu in the Flight Data map. On the STorM32 side the camera trigger can be easily tested by connecting a visible-light LED (red, green, blue, not IR) to the #IR port.
 
* '''''Gimbal RC Targeting''''': With the ArduPilot mount in RC Targeting mode (which should be the default setting), the camera can be moved with the transmitter sticks.
 
* '''''Sniffing the communication''''': One of course can sniff directly what is going on on the communication data lines. This is especially helpful when using CAN/UAVCAN. You when need a SLCAN adapter, e.g., the [http://www.olliw.eu/2017/uavcan-for-hobbyists/ UC4H SLCAN adapter].
 
== Gimbal Point ==
 
MissionPlanner supports what it calls a gimbal point. It is a blue point icon on the map, which indicates the estimated position at which the gimbal is looking at (see also e.g. https://github.com/ArduPilot/MissionPlanner/issues/1323). In order to activate it, the following ArduPilot parameters must be set:
 
'''''Settings in ArduPilot:'''''
* MNT_STAB_ROLL = 0
* MNT_STAB_TILT = 1

Latest revision as of 09:00, 28 January 2024

The information on this page refers to firmware v2.64e, and higher.

The STorM32 gimbal controller can communicate with an ArduPilot flight controller via a serial UART data link. The serial communication allows for a much richer data transmission and accordingly richer set of features than possible with the traditional connections such as PWM, PPM, SBUS, CRSF, and alike.

If you only need the range of functionality possible with the conventional tilt & pan control, then you may not need anything of the following. Some of the basic features can also be accomplished in traditional ways. Decide yourself which approach fits your needs best. :)

If you want to make best use of your STorM32 gimbal and want 2020-ish capabilities, then you may want to chose BetaPilot (BetaCopter/BetaPlane). This fork of ArduPilot is specifically designed for the STorM32 gimbal controller, and provides the best range of functions. For details see Using STorM32 with BetaPilot.

STorM32 - ArduPilot Support

ArduPilot offers three mount types, which can in principle be used with the STorM32 controller:

  • SToRM32 MAVLink: MNTx_TYPE = 4
  • SToRM32 Serial: MNTx_TYPE = 5
  • Greemsy: MNTx_TYPE = 6

For further details on the first two mounts, and instructions on how to use them, please visit ArduPilot Docs > Copter > Optional Hardware > Camera&Gimbals > SToRM32 Gimbal Controller.

The SToRM32 Serial mount (MNTx_TYPE = 5) does not work with v2.xx firmwares, and should not be considered except for legacy I2C setups running v0.9x firmware.

The Greemsy mount (MNTx_TYPE = 6) is MAVLink based, and thus can in principle be used with STorM32. This mount in fact exploits the 'new' gimbal messages of the gimbal protocol v2, and would offer some real benefits. However, it unfortuntaley violates and breaks the MAVLink standard in various respects, and interoperability with STorM32 is thus mixed.

The SToRM32 MAVLink mount (MNTx_TYPE = 4) currently appears to work best with STorM32 in the sense that it produces the least issues, but it is quite limited in its functionality.

For both the SToRM32 MAVLink (MNTx_TYPE = 4) and Greemsy (MNTx_TYPE = 6) mounts, it is not fully clear what works and what does not work at the time of writing, but the SToRM32 MAVLink mount (MNTx_TYPE = 4) should work fine with respect to controlling a STorM32 gimbal.

Disclaimer: ArduPilot's gimbal support is a constant source of issues, in terms of incompatibilities with the official MAVLink standard and/or flaws, and the details can quite vary with the ArduPilot firmware version. Also the ArduPilot documentation can be out-of-date. Please note that STorM32 can't do anything about this, it's ArduPilot, and please also note that the STorM32 firmware author is neither responsible for the implementation of ArduPilot's mount types nor for ArduPilot's documentation.

Virtual Channel Configuration

ArduPilot does not emit the RC_CHANNELS MAVLink message by default, which could be desired for taking advantage of the STorM32's virtual channel feature.

It can be activated in the flight controller by setting the SRx_RC_CHAN parameter to a non-zero value, where 'x' refers to the stream associated to the serial port which is used for the MAVLink communication with the STorM32 controller.

For more details on the feature see Virtual Channel Configuration.

Testing the Connection

The serial MAVLink connection can be tested in several ways. Suggestions can be found in Using STorM32 with BetaPilot: Testing the Connection. They may not all work with native ArduPilot, but many will.

Retrieved from "http:///storm32bgc-wiki/index.php?title=Using_STorM32_with_ArduPilot&oldid=11450"