Using STorM32 with ArduPilot: Difference between revisions

From STorM32-BGC Wiki
Jump to navigation Jump to search
Tag: Manual revert
 
(454 intermediate revisions by 2 users not shown)
Line 1: Line 1:
The STorM32 gimbal controller can communicate with an [http://ardupilot.org/ardupilot/index.html ArduPilot] flight controller via (i) a serial data line or (ii) the CAN bus using UAVCAN. The serial/UAVCAN communication allows for a much richer data transmission and accordingly richer set of features than possible with the traditional PWM connections. It also leads to a clean wiring.
''The information on this page refers to firmware v2.64e, and higher.''


Two aspects of the communication can be distinguished:
The STorM32 gimbal controller can communicate with an [http://ardupilot.org/ardupilot/index.html ArduPilot] flight controller via a serial UART data link. The serial communication allows for a much richer data transmission and accordingly richer set of features than possible with the traditional connections such as PWM, PPM, SBUS, CRSF, and alike.
* '''''Control of the gimbal:''''' The serial/UAVCAN communication allows us to control the orientation of the gimbal, with higher precision than possible with the standard inputs, and gives access to all other features of the STorM32 controller, such as triggering a camera, executing on-board scripts, and so on. It also allows the STorM32 to feed back information to the flight controller and the ground station, such as the actual camera orientation, which can be displayed by a ground station or OSD. Advanced operation modes, which in addition involves the flight controller, ground station, companion computer, or other electronics, such as follow me or object tracking, also fall into that category.
* '''''Improved stabilization:''''' In addition, the serial/UAVCAN communication is used to transfer dedicated data from the flight controller to the STorM32 controller, which helps in achieving better stabilization, and hence better videos. For instance, yaw drift can be corrected, horizon shifts in high-speed turns removed, or smoother pans achieved. This part of the serial/UAVCAN communication is called the [http://www.rcgroups.com/forums/showthread.php?t=2395475 STorM32-Link].
This article is mostly concerned with the first aspect, also because the STorM32-Link is not yet fully developed.


If you just need the range of functionality possible with the standard tilt & pan control, then you don't need anything of the following, and you may stop reading here. Also, some of the features discussed below can be accomplished by workarounds. Decide yourself which approach fits your needs best. :)
If you only need the range of functionality possible with the conventional tilt & pan control, then you may not need anything of the following. Some of the basic features can also be accomplished in traditional ways. Decide yourself which approach fits your needs best. :)


== STorM32 - ArduPilot Support ==
If you want to make best use of your STorM32 gimbal and want 2020-ish capabilities, then you may want to chose [https://github.com/olliw42/BetaPilot BetaPilot] (BetaCopter/BetaPlane). This fork of ArduPilot is specifically designed for the STorM32 gimbal controller, and provides the best range of functions. For details see [[Using STorM32 with BetaPilot]].


Four modes of operation are available:
<div class="toclimit-3">__TOC__</div>


=== STorM32 Mavlink ===
== STorM32 - ArduPilot Support ==
 
* MNT_TYPE = 4
* SERIALx_PROTOCOL = 1
* STorM32 heartbeat must be activated, {{PARAMNAME|Mavlink Configuration}} = {{PARAMVALUE|emit heartbeat}} or higher
* available in ArduPilot and BetaCopter
 
For further details please visit [http://ardupilot.org/copter/docs/common-storm32-gimbal.html#common-storm32-gimbal| ArduPilot Docs > Copter > Optional Hardware > Camera&Gimbals > SToRM32 Gimbal Controller]. A good sum-up by lvale is found here [http://www.rcgroups.com/forums/showpost.php?p=35263645&postcount=154], and a workaround to access further STorM32 functions here [http://www.rcgroups.com/forums/showpost.php?p=34415407&postcount=115].


=== STorM32 Serial ===
'''''ArduPilot''''' offers three mount types, which can in principle be used with the STorM32 controller:


* MNT_TYPE = 5 (the arducopter documentation is wrong here)
* '''''SToRM32 MAVLink''''': MNTx_TYPE = 4
* SERIALx_PROTOCOL = 8
* '''''SToRM32 Serial''''': MNTx_TYPE = 5
* STorM32 heartbeat must be deactivated, {{PARAMNAME|Mavlink Configuration}} = {{PARAMVALUE|no heartbeat}}
* '''''Greemsy''''': MNTx_TYPE = 6
* available in ArduPilot and BetaCopter


For further details please visit [http://ardupilot.org/copter/docs/common-storm32-gimbal.html#common-storm32-gimbal| ArduPilot Docs > Copter > Optional Hardware > Camera&Gimbals > SToRM32 Gimbal Controller].
For further details on the first two mounts, and instructions on how to use them, please visit [http://ardupilot.org/copter/docs/common-storm32-gimbal.html#common-storm32-gimbal| ArduPilot Docs > Copter > Optional Hardware > Camera&Gimbals > SToRM32 Gimbal Controller].


=== STorM32 UAVCAN ===
The ''SToRM32 Serial'' mount (MNTx_TYPE = 5) does not work with v2.xx firmwares, and should not be considered except for legacy I2C setups running v0.9x firmware.


* MNT_TYPE = 83
The ''Greemsy'' mount (MNTx_TYPE = 6) is MAVLink based, and thus can in principle be used with STorM32. This mount in fact exploits the 'new' gimbal messages of the [https://mavlink.io/en/services/gimbal_v2.html gimbal protocol v2], and would offer some real benefits. However, it unfortuntaley violates and breaks the MAVLink standard in various respects, and interoperability with STorM32 is thus mixed.
* CAN_P1_DRIVER = 1
* STorM32 heartbeat must be deactivated, {{PARAMNAME|Mavlink Configuration}} = {{PARAMVALUE|no heartbeat}}
* available only in BetaCopter


{{COMMENT|The CAN bus on the flight controller must be activated properly. This can require that also other parameters in the CAN section must be set appropriately. Please consult the [http://ardupilot.org/ardupilot/ ArduPilot Docs]}}
The ''SToRM32 MAVLink'' mount (MNTx_TYPE = 4) currently appears to work best with STorM32 in the sense that it produces the least issues, but it is quite limited in its functionality.


=== STorM32 Native ===
For both the ''SToRM32 MAVLink'' (MNTx_TYPE = 4) and ''Greemsy'' (MNTx_TYPE = 6) mounts, it is not fully clear what works and what does not work at the time of writing, but the ''SToRM32 MAVLink'' mount (MNTx_TYPE = 4) should work fine with respect to controlling a STorM32 gimbal.


* MNT_TYPE = 84
'''''Disclaimer''': ArduPilot's gimbal support is a constant source of issues, in terms of incompatibilities with the official MAVLink standard and/or flaws, and the details can quite vary with the ArduPilot firmware version. Also the ArduPilot documentation can be out-of-date. Please note that STorM32 can't do anything about this, it's ArduPilot, and please also note that the STorM32 firmware author is neither responsible for the implementation of ArduPilot's mount types nor for ArduPilot's documentation.''
* SERIALx_PROTOCOL = 84
* STorM32 heartbeat must be deactivated, {{PARAMNAME|Mavlink Configuration}} = {{PARAMVALUE|no heartbeat}}
* available only in BetaCopter


The STorM32 UAVCAN and STorM32 Native modes are essentially identical, except that the data communication in the former case is via the CAN bus using the UAVCAN protocol, and in the latter case via the selected serial port.
== Virtual Channel Configuration ==


The remainder of this wiki page is devoted exclusively to describing the STorM32 UAVCAN/Native modes; the STorM32 UAVCAN mode is chosen exemplarily.
ArduPilot does not emit the RC_CHANNELS MAVLink message by default, which could be desired for taking advantage of the STorM32's virtual channel feature.


=== Feature Matrix ===
It can be activated in the flight controller by setting the SRx_RC_CHAN parameter to a non-zero value, where 'x' refers to the stream associated to the serial port which is used for the MAVLink communication with the STorM32 controller.


For more details on the feature see [[Using_STorM32_with_BetaPilot#Virtual_Channel_Configuration|Virtual Channel Configuration]].
<!--
== Feature Matrix ==
(for ArduPilot 4.2)(the status for ArduPilot 4.3 is presently unclear)(all to the best of the authors knowledge)
{| class="wikitable" style="text-align: center;"
{| class="wikitable" style="text-align: center;"
!Feature
!Feature
!STorM32 Mavlink
!Traditional<br>PWM, PPM, SBUS, ...
!STorM32 Serial
!SToRM32 MAVLink<br>(MNT_TYPE = 4)
!STorM32 UAVCAN
!SToRM32 Serial<br>(MNT_TYPE = 5)
!BetaPilot<br> STorM32 MAVLink2<br>(MNT_TYPE = 83)
|-
| style="text-align:left;" | Gimbal Angle Control || style="background-color: lightgreen;"| x || style="background-color: #d2f8d2;"| x <sup>(?)</sup> || style="background-color: lightgreen;"| x || style="background-color: lightgreen;"| x
|-
| style="text-align:left;" | MOUNT_STATUS message || - || style="background-color: #d2f8d2;"| x <sup>(1)</sup> || style="background-color: #d2f8d2;"| x <sup>(2)</sup> || style="background-color: lightgreen;"| x
|-
| style="text-align:left;" | ATTITUDE message || - || - || - || style="background-color: lightgreen;"| x
|-
| style="text-align:left;" | Camera Trigger || style="background-color: lightgreen;"| x || style="background-color: lightgreen;"| x || - || style="background-color: lightgreen;"| x
|-
| style="text-align:left;" | Gimbal Point in MP || - || style="background-color: lightgreen;"| x || style="background-color: #d2f8d2;"| x <sup>(2)</sup> || style="background-color: lightgreen;"| x
|-
| style="text-align:left;" | Solo Smart Shots || style="background-color: #d2f8d2;"| x <sup>(3)|| - || - || style="background-color: #d2f8d2;"| x <sup>(3)</sup>
|-
| style="text-align:left;" | Camera Manager in QGC || - || style="background-color: lightgreen;"| x || - || style="background-color: lightgreen;"| x
|-
| style="text-align:left;" | MAVLink Parameters || - || style="background-color: lightgreen;"| x || - || style="background-color: lightgreen;"| x
|-
| style="text-align:left;" | Video Control in Missions || - || style="background-color: lightgreen;"| x || - || style="background-color: lightgreen;"| x
|-
| style="text-align:left;" | 360° Gimbal with Free Look || style="background-color: lightgreen;"| x || - || - || style="background-color: lightgreen;"| x
|-
| style="text-align:left;" | STorM32 Functions || style="background-color: lightgreen;"| x || - || - || style="background-color: lightgreen;"| x
|-
|-
| style="text-align:left;" | Gimbal Angle Control || style="background-color: lightgreen;"| x || style="background-color: lightgreen;"| x || style="background-color: lightgreen;"| x
| style="text-align:left;" | STorM32 Scripts || style="background-color: lightgreen;"| x || - || - || style="background-color: lightgreen;"| x
|-
|-
| style="text-align:left;" | Camera Trigger || style="background-color: lightgreen;"| x (?) || - || style="background-color: lightgreen;"| x
| style="text-align:left;" | STorM32-Link: Horizon Drift Comp. || - || - || - || style="background-color: lightgreen;"| x <sup></sup>
|-
|-
| style="text-align:left;" | MAV_MOUNT_STATUS message || style="background-color: lightgreen;"| x || style="background-color: lightgreen;"| x || style="background-color: lightgreen;"| x
| style="text-align:left;" | STorM32-Link: Yaw Drift Comp. || - || - || - || style="background-color: lightgreen;"| x <sup></sup>
|-
|-
| style="text-align:left;" | Video on/off || - || - || style="background-color: lightgreen;"| x
| style="text-align:left;" | MAVLink Passthrough Configuration || - || style="background-color: lightgreen;"| x || - || style="background-color: lightgreen;"| x
|-
|-
| style="text-align:left;" | Extended Gimbal Angle Control || - || - || style="background-color: lightgreen;"| x
| style="text-align:left;" | MAVLink Camera Microservice || - || style="background-color: lightgreen;"| x || - || style="background-color: lightgreen;"| x
|-
|-
| style="text-align:left;" | 360° Gimbal with Free Look || - || - || style="background-color: lightgreen;"| x
| style="text-align:left;" | MAVLink Advanced Features || - || - || - || style="background-color: lightgreen;"| x
|-
|-
| style="text-align:left;" | STorM32 Functions || - || - || style="background-color: lightgreen;"| x
| style="text-align:left;" | MAVLink Statustext messages || - || - || - || style="background-color: lightgreen;"| x
|-
|-
| style="text-align:left;" | STorM32 Scripts || - || - || style="background-color: lightgreen;"| x
| style="text-align:left;" | STorM32 Gimbal Protocol || - || - || - || style="background-color: lightgreen;"| x
|-
|-
| style="text-align:left;" | STorM32-Link || - || - || style="background-color: lightgreen;"| x
| style="text-align:left;" | Prearm Checks || - || - || - || style="background-color: lightgreen;"| x
|}
|}


== BetaCopter ==
(?) Many but not all features work in the latest ArduPilot releases. Please check with the ArduPilot community.
 
I made some modifications to the ArduCopter firmware (currently AC3.6-dev) and called the result BetaCopter. However, unless the STorM32-specific features are activated by a "secret key" 83 or 84, BetaCopter will - to the best of my knowledge - behave exactly like the original firmware. This means that - to the best of my knowledge - there is no risk involved in using BetaCopter instead of ArduCopter.
 
For the following you need betacopter 3.6dev v005 and o323bgc v2.31e, or higher. You can download the latest versions from here: [[Downloads]].
 
On the STorM32 controller the parameter {{PARAMNAME|Mavlink Configuration}} '''''must''''' be set to {{PARAMVALUE|no heartbeat}}. For using CAN/UAVACN, please see the article [[UAVCAN]].
 
The following settings or parameter fields are available. The features involve settings on both the BetaCopter and STorM32 side.
 
=== ArduCopter: MNT_TYPE = 83 or 84 ===
 
As mount type you may choose 83 or 84, which activates BetaCopter's UAVCAN or native STorM32 protocol. You should then notice this:
 
* All ArduCopter camera features are working. That is, whenever a certain path of actions (Mavlink, receiver, mission, UAVCAN, ...) lets ArduCopter want to take a picture, the STorM32 controller will know and activate it's camera functions.
* All ArduCopter mount features are working. Well, that's mostly exactly what you get also with the other modes of operation, e.g. when using the Mavlink connection with ArduPilot. However, you also get some enhancements, see the next sub chapter.
* In the Message box of MissonPlanner "STorM32 ..." messages will appear (currently only for MNT_TYPE = 84).
 
=== STorM32: Virtual Channel Configuration = serial ===
 
In the STorM32 GUI, the parameter {{PARAMNAME|Virtual Channel Configuration}} can be set to {{PARAMVALUE|serial}}, which has this effect:
 
All STorM32 [[Inputs and Functions|functions]] can be invoked by selecting a {{PARAMVALUE|Virtual-1}} - {{PARAMVALUE|Virtual-16}} input channel, as if the STorM32 would be directly connected to the receiver. This allows doing many useful things, such as activating a script or triggering video on/off from the transmitter. It however also allows doing nonsense, and it is the users responsibility to avoid that. For instance, if the ArduPilot mount is activated and is in Rc Targeting mode, and e.g. {{PARAMNAME|Rc Pitch Control}} is set to a virtual input channel, then the gimbal may move in funny ways since it may receive the transmitter stick information from both the ArduPilot mount and the receiver. In contrast, if the ArduPilot mount is in GPS or ROI Targeting mode, then one gets "free look", which is useful and quite cool actually. As said, all that is exactly as if the receiver would be directly connected to the STorM32 on its RC ports.
 
=== STorM32-Link ===
 
With MNT_TYPE = 83 or 84 you have also activated the STorM32-Link (for details on the STorM32-Link see [http://www.rcgroups.com/forums/showthread.php?t=2395475]). In the STorM32 GUI, specifically the {{GUI|Dashboard}} and/or the {{GUI|Data Display}}, you should note that the STorM32-Link field goes ON.
 
The main parts of the STorM32-Link functionality are not yet implemented in the STorM32 firmware. However, as evidenced by the STorM32-Link field going ON, the data exchange is established.
 
== Testing the Serial Connection ==
 
The serial connection can be tested in several ways. The following tests do not require that the copter is completely built, and do not require that the copter is armed.
 
* '''''Message box in MissonPlanner''''': In the message box several messages related to the STorM32 should appear. In particular, a message like "STorM32 v2.11e nt v1.30 F103RC" informing about the STorM32 firmware version should be visible. Also, a message "STorM32 in NORMAL mode" should occur when the gimbal has finished initialization and entered NORMAL mode.
 
* '''''STorM32-Link field in the STorM32 GUI''''': The {{GUI|Dashboard}} and {{GUI|Data Display}} each have a field which is related to the STorM32-Link. They should display OK or a similar positive message.


* '''''Trigger Camera NOW''''': In MissionPlanner the camera can be triggered by a right-mouse-click dropdown menu in the Flight Data map. On the STorM32 side the camera trigger can be easily tested by connecting a visible-light LED (red, green, blue, not IR) to the #IR port.
(1) The message reports the last set point, not the actual gimbal/camera orientation.


* '''''Gimbal RC Targeting''''': With the ArduPilot mount in RC Targeting mode (which should be the default setting), the camera can be turned with the transmitter sticks.
(2) Works only for deprecated v0.9x firmwares.


== Gimbal Point ==
(3) Only up to ArduCopter 3.6. ArduCopter 4.0 has introduced two bugs which the STorM32 controller cannot work around.
-->


MissionPlanner supports what it calls a gimbal point. It is a blue point icon on the map, which indicates the estimated position at which the gimbal is looking at (see also e.g. https://github.com/ArduPilot/MissionPlanner/issues/1323). In order to activate it, the following ArduPilot parameters must be set:
== Testing the Connection ==


* MNT_STAB_ROLL = 0
The serial MAVLink connection can be tested in several ways. Suggestions can be found in [[Using_STorM32_with_BetaPilot#Testing_the_Connection | Using STorM32 with BetaPilot: Testing the Connection]]. They may not all work with native ArduPilot, but many will.
* MNT_STAB_TILT = 1

Latest revision as of 09:00, 28 January 2024

The information on this page refers to firmware v2.64e, and higher.

The STorM32 gimbal controller can communicate with an ArduPilot flight controller via a serial UART data link. The serial communication allows for a much richer data transmission and accordingly richer set of features than possible with the traditional connections such as PWM, PPM, SBUS, CRSF, and alike.

If you only need the range of functionality possible with the conventional tilt & pan control, then you may not need anything of the following. Some of the basic features can also be accomplished in traditional ways. Decide yourself which approach fits your needs best. :)

If you want to make best use of your STorM32 gimbal and want 2020-ish capabilities, then you may want to chose BetaPilot (BetaCopter/BetaPlane). This fork of ArduPilot is specifically designed for the STorM32 gimbal controller, and provides the best range of functions. For details see Using STorM32 with BetaPilot.

STorM32 - ArduPilot Support

ArduPilot offers three mount types, which can in principle be used with the STorM32 controller:

  • SToRM32 MAVLink: MNTx_TYPE = 4
  • SToRM32 Serial: MNTx_TYPE = 5
  • Greemsy: MNTx_TYPE = 6

For further details on the first two mounts, and instructions on how to use them, please visit ArduPilot Docs > Copter > Optional Hardware > Camera&Gimbals > SToRM32 Gimbal Controller.

The SToRM32 Serial mount (MNTx_TYPE = 5) does not work with v2.xx firmwares, and should not be considered except for legacy I2C setups running v0.9x firmware.

The Greemsy mount (MNTx_TYPE = 6) is MAVLink based, and thus can in principle be used with STorM32. This mount in fact exploits the 'new' gimbal messages of the gimbal protocol v2, and would offer some real benefits. However, it unfortuntaley violates and breaks the MAVLink standard in various respects, and interoperability with STorM32 is thus mixed.

The SToRM32 MAVLink mount (MNTx_TYPE = 4) currently appears to work best with STorM32 in the sense that it produces the least issues, but it is quite limited in its functionality.

For both the SToRM32 MAVLink (MNTx_TYPE = 4) and Greemsy (MNTx_TYPE = 6) mounts, it is not fully clear what works and what does not work at the time of writing, but the SToRM32 MAVLink mount (MNTx_TYPE = 4) should work fine with respect to controlling a STorM32 gimbal.

Disclaimer: ArduPilot's gimbal support is a constant source of issues, in terms of incompatibilities with the official MAVLink standard and/or flaws, and the details can quite vary with the ArduPilot firmware version. Also the ArduPilot documentation can be out-of-date. Please note that STorM32 can't do anything about this, it's ArduPilot, and please also note that the STorM32 firmware author is neither responsible for the implementation of ArduPilot's mount types nor for ArduPilot's documentation.

Virtual Channel Configuration

ArduPilot does not emit the RC_CHANNELS MAVLink message by default, which could be desired for taking advantage of the STorM32's virtual channel feature.

It can be activated in the flight controller by setting the SRx_RC_CHAN parameter to a non-zero value, where 'x' refers to the stream associated to the serial port which is used for the MAVLink communication with the STorM32 controller.

For more details on the feature see Virtual Channel Configuration.

Testing the Connection

The serial MAVLink connection can be tested in several ways. Suggestions can be found in Using STorM32 with BetaPilot: Testing the Connection. They may not all work with native ArduPilot, but many will.

Retrieved from "http:///storm32bgc-wiki/index.php?title=Using_STorM32_with_ArduPilot&oldid=11450"